- #Polaris digital wrench wireless setup install#
- #Polaris digital wrench wireless setup license#
- #Polaris digital wrench wireless setup Bluetooth#
If you have a little patience, the factory tester (or the homade one) and a multimeter, this is one of the least inimidating processes on the sled. lock it down (I like to use low strength wick-n-lock locktite on this screw after it is locked down. THEN you open the throttle plates with the Idle screw to: THEN you adjust the TPS to the closed throttle plates at :ĩ00/755 CFi. This is an independent adjustment of both TB's. The baseline calibration IS with the throttle plates closed. Once the TPS voltage is verified and set, remove the sensor Voltage at the yellow terminal should be. Turn the idle set screw clockwise until the voltage reads. Tighten the TPS retaining screws, making sure that the voltage continues to read. Adjust the TPS sensor until the voltage on the volt meter reads. Turn the synchronization screw clockwise until the volt meter reads the voltage level that you noted in step #8.ġ3. Insert the synchronization lever tab spring and screw.ġ1. Remove the synchronization lever tab spring (E) and gently open and then close the throttle plateswith the throttle, allowing Place a shop towel under the throttle body incase you loose grip on the spring or thread a small wire around it if it should fall.ĩ.
#Polaris digital wrench wireless setup install#
Remove the connector from the TPS on the throttle body and install TPS sensor tool on to the TPS.Ĩ. Turn the synchronization screw (C) counterclockwise until the synchronization lever is touching the synchronization screwħ. Back off the idle lock nut counterclockwise and then back out the idle adjuster (A) counterclockwise until the screw tip (B)Ħ. Remove the throttle cable in order to take the slack out of the cable.ĥ. NOTE: The Fluke meter will change scales and show O.L. Slowly open throttle and check for smooth voltage change. Insert the red voltmeter lead into the terminal above the pink wire, and the black meter lead to the terminal above the black Terminal and the red probe into the pink terminal. Make sure your 9 volt battery is in good condition by inserting the black voltmeter probe from your Fluketmeter in the black Assemble your TPS sensor tool (PN 2201519) as per the instructions that came with the tool.Ģ. If replacing a TPS or resetting the TPS, Polaris has developed a TPS test kit for aid in setting the Throttle Position Sensor to specification.ġ. Click here to learn more.The TPS comes set from the factory and should not need any adjustments.
#Polaris digital wrench wireless setup license#
Radio models include, but are not limited to: RDM-DB, M1, RDH-X, R1, V3, RM60, RH5R, RDH16, as well as Icom, Motorola, Kenwood business band radios, and more.īusiness License is required. This radio works with all VHF business band radios operating on the same frequencies. The complete communication experience for your Polaris RZR!įits: Polaris RZR, XP1, XP4, XPS, XP 1000, Turbo S, 1000S, 900S, and Trail 1000 This kit includes everything you need to take the conversation further. The enhanced music controls allow you to shuffle through your music directly from the faceplate of the intercom. The high output amplifier provides high fidelity audio for the best in music enjoyment.
#Polaris digital wrench wireless setup Bluetooth#
Easily connect to Ride Command, GPS, or any Bluetooth device. The M1 mobile radio works with all digital and analog VHF radios, and all DMR digital radios: Motorola, Rugged, etc.įor music and phone calls, simply pair your phone using the onboard Bluetooth and you’re ready to stream. Again, the music dims and you're ready to talk through our crystal clear M1 digital mobile business band radio. Ready to talk to other vehicles in your group? Simply press the included PTT (push-to-talk) on the steering wheel or grab-bar to transmit. Just start talking and the auto music-dimming attenuates your music, making conversation easy.
Our RRP696 intercom allows you to talk to passengers without yelling, directly through the headsets or helmet kits. Talk between passengers, communicate with other vehicles, listen to music, and make phone calls - our complete communication kits do it all! This kit features a custom mounting solution that perfectly fits your UTV.